Corner Feet for BenchDog Tools Ultra MFT Workstation (Download & Print)
THIS IS A DOWNLOADABLE FILE-SET FOR CUSTOMERS TO PRINT AT HOME
For the physical feet, printed in Black PETG, see: <Link Here>
Raise your BenchDog Tools Ultra MFT Workstation of a cabinet or workbench with these smart looking corner feet. While designed around the BenchDogs MFT, these feet are also compatible with any 4040 profile with a 10mm slot.
Dimensions:
Width: 160mm
Length: 160mm
Height: 82mm
Printed Weight for 4 feet (with fittings): 850-900g
The key consideration in the design of the feet was to match the bench height of a FESTOOL MFT/3 when its legs were folded and the unit situated on a cabinet or low-bench within a workshop set-up. Additionally, the design allows for the feet to remain attached to the bench with sufficient clearance for the legs to be lowered and secured without any modification to the bench.
Recommended Print Settings:
Filament: PETG (Recommended), PLA+
Perimeters: Increase to 4 (recommended),
Top & Bottom Layers: 4
Infill: 15% (Recommended for high strength & impact resistance), or 5-10% to save weight/material.
Note: 10% allows all 4 feet to be printed from a 1 kilogram of filament.
Note: ABS is not a recommended filament material unless you have experience of, and success with, large volume prints on your machines. Additionally, a closed chamber, such as those of a Bambu Labs X or P series, would be required to minimise warping on the print-bed.
Prusa i3 MK4 Print Estimates, per foot.
Print Time: 7 h 41m
Filament Use (estimate) : 266g at 15% infill, 230g @ 10% infill, 191g @ 5% infill
The STLs are supplied in the correct orientation for printing. The slot lug, should be on the top and no supports are required. Holes are printed using overhangs so some clean-up will be required post-print. A simple method is to use a 8mm twist drill bit into the hole by hand or using a hand-drill at low-speed.
Additional Components / Bill of Materials:
You will require additional fixings to attach the corner feet to your bench. Affiliate links to Amazon.co.uk are provided:
16 x M8 Sprint Tee Nuts for 10mm slots - https://amzn.to/3NIGI0y
16 x M8 Hex Socket Cap bolts: Length 20mm - https://amzn.to/4e2Xsdp
4 × 4.0mm x 30 countersink screws (optional for Bench Mounting Pegs)
Washers are not required. Take care not to over tighten bolts.
Print Files
Provided in 3MF format (Recommended) and STL Format
Universal Corner Foot (82mm High)
Universal Corner Foot (82mm High) with Strawbyte logo embossed on one face.
Bench Mounting Pegs printed on positioning sheet. An optional part to allow the feet to locate into and be secured to the cabinet/bench it is placed on. Use on the front-most feet.
Other Files
Non-transferrable End user licence
Instructions (a version of this item description).
Copyright & End User Licence Information
Karl J. Pountney, trading as Strawbyte Workshop, asserts his rights as the sole creator of the design and downloadable files under the Copyright, Designs and Patents Act of the United Kingdom. Reproductions are solely permitted under a single, non-transferrable licence issued to the purchaser of these files.
The licence is for the sole use of the purchaser and prohibits commercial sale of products derived from the included print-files. If printing for others, we ask that a licence is purchased for each user of the product.
THIS IS A DOWNLOADABLE FILE-SET FOR CUSTOMERS TO PRINT AT HOME
For the physical feet, printed in Black PETG, see: <Link Here>
Raise your BenchDog Tools Ultra MFT Workstation of a cabinet or workbench with these smart looking corner feet. While designed around the BenchDogs MFT, these feet are also compatible with any 4040 profile with a 10mm slot.
Dimensions:
Width: 160mm
Length: 160mm
Height: 82mm
Printed Weight for 4 feet (with fittings): 850-900g
The key consideration in the design of the feet was to match the bench height of a FESTOOL MFT/3 when its legs were folded and the unit situated on a cabinet or low-bench within a workshop set-up. Additionally, the design allows for the feet to remain attached to the bench with sufficient clearance for the legs to be lowered and secured without any modification to the bench.
Recommended Print Settings:
Filament: PETG (Recommended), PLA+
Perimeters: Increase to 4 (recommended),
Top & Bottom Layers: 4
Infill: 15% (Recommended for high strength & impact resistance), or 5-10% to save weight/material.
Note: 10% allows all 4 feet to be printed from a 1 kilogram of filament.
Note: ABS is not a recommended filament material unless you have experience of, and success with, large volume prints on your machines. Additionally, a closed chamber, such as those of a Bambu Labs X or P series, would be required to minimise warping on the print-bed.
Prusa i3 MK4 Print Estimates, per foot.
Print Time: 7 h 41m
Filament Use (estimate) : 266g at 15% infill, 230g @ 10% infill, 191g @ 5% infill
The STLs are supplied in the correct orientation for printing. The slot lug, should be on the top and no supports are required. Holes are printed using overhangs so some clean-up will be required post-print. A simple method is to use a 8mm twist drill bit into the hole by hand or using a hand-drill at low-speed.
Additional Components / Bill of Materials:
You will require additional fixings to attach the corner feet to your bench. Affiliate links to Amazon.co.uk are provided:
16 x M8 Sprint Tee Nuts for 10mm slots - https://amzn.to/3NIGI0y
16 x M8 Hex Socket Cap bolts: Length 20mm - https://amzn.to/4e2Xsdp
4 × 4.0mm x 30 countersink screws (optional for Bench Mounting Pegs)
Washers are not required. Take care not to over tighten bolts.
Print Files
Provided in 3MF format (Recommended) and STL Format
Universal Corner Foot (82mm High)
Universal Corner Foot (82mm High) with Strawbyte logo embossed on one face.
Bench Mounting Pegs printed on positioning sheet. An optional part to allow the feet to locate into and be secured to the cabinet/bench it is placed on. Use on the front-most feet.
Other Files
Non-transferrable End user licence
Instructions (a version of this item description).
Copyright & End User Licence Information
Karl J. Pountney, trading as Strawbyte Workshop, asserts his rights as the sole creator of the design and downloadable files under the Copyright, Designs and Patents Act of the United Kingdom. Reproductions are solely permitted under a single, non-transferrable licence issued to the purchaser of these files.
The licence is for the sole use of the purchaser and prohibits commercial sale of products derived from the included print-files. If printing for others, we ask that a licence is purchased for each user of the product.
THIS IS A DOWNLOADABLE FILE-SET FOR CUSTOMERS TO PRINT AT HOME
For the physical feet, printed in Black PETG, see: <Link Here>
Raise your BenchDog Tools Ultra MFT Workstation of a cabinet or workbench with these smart looking corner feet. While designed around the BenchDogs MFT, these feet are also compatible with any 4040 profile with a 10mm slot.
Dimensions:
Width: 160mm
Length: 160mm
Height: 82mm
Printed Weight for 4 feet (with fittings): 850-900g
The key consideration in the design of the feet was to match the bench height of a FESTOOL MFT/3 when its legs were folded and the unit situated on a cabinet or low-bench within a workshop set-up. Additionally, the design allows for the feet to remain attached to the bench with sufficient clearance for the legs to be lowered and secured without any modification to the bench.
Recommended Print Settings:
Filament: PETG (Recommended), PLA+
Perimeters: Increase to 4 (recommended),
Top & Bottom Layers: 4
Infill: 15% (Recommended for high strength & impact resistance), or 5-10% to save weight/material.
Note: 10% allows all 4 feet to be printed from a 1 kilogram of filament.
Note: ABS is not a recommended filament material unless you have experience of, and success with, large volume prints on your machines. Additionally, a closed chamber, such as those of a Bambu Labs X or P series, would be required to minimise warping on the print-bed.
Prusa i3 MK4 Print Estimates, per foot.
Print Time: 7 h 41m
Filament Use (estimate) : 266g at 15% infill, 230g @ 10% infill, 191g @ 5% infill
The STLs are supplied in the correct orientation for printing. The slot lug, should be on the top and no supports are required. Holes are printed using overhangs so some clean-up will be required post-print. A simple method is to use a 8mm twist drill bit into the hole by hand or using a hand-drill at low-speed.
Additional Components / Bill of Materials:
You will require additional fixings to attach the corner feet to your bench. Affiliate links to Amazon.co.uk are provided:
16 x M8 Sprint Tee Nuts for 10mm slots - https://amzn.to/3NIGI0y
16 x M8 Hex Socket Cap bolts: Length 20mm - https://amzn.to/4e2Xsdp
4 × 4.0mm x 30 countersink screws (optional for Bench Mounting Pegs)
Washers are not required. Take care not to over tighten bolts.
Print Files
Provided in 3MF format (Recommended) and STL Format
Universal Corner Foot (82mm High)
Universal Corner Foot (82mm High) with Strawbyte logo embossed on one face.
Bench Mounting Pegs printed on positioning sheet. An optional part to allow the feet to locate into and be secured to the cabinet/bench it is placed on. Use on the front-most feet.
Other Files
Non-transferrable End user licence
Instructions (a version of this item description).
Copyright & End User Licence Information
Karl J. Pountney, trading as Strawbyte Workshop, asserts his rights as the sole creator of the design and downloadable files under the Copyright, Designs and Patents Act of the United Kingdom. Reproductions are solely permitted under a single, non-transferrable licence issued to the purchaser of these files.
The licence is for the sole use of the purchaser and prohibits commercial sale of products derived from the included print-files. If printing for others, we ask that a licence is purchased for each user of the product.